Answering 24/7, projects by appointment
Solar Panel Removal and Reinstall for Atlanta Roof Work
A roof under solar panels still wears out. The trick is getting the panels off and back on without trading a roof leak for a mount leak.
At a glance
- 24/7
- Calls answered
- Every mount
- Reflashed
- One schedule
- Roof and array together
- Atlanta
- Service office
Solar panel removal and reinstall in Atlanta is needed whenever the roof under an array is repaired or replaced: the panels and racking come off, the roof is redone, every mount is flashed into the new shingles, and the array goes back on. Because each rail attachment is a hole in the roof, the reflashing is what decides whether the job stays dry.
Updated September 2026
The job
Why Reroofing Under Solar Needs a Plan
Solar arrays are often installed on roofs with ten or fifteen years already on them, which means the shingles give out while the panels still have decades left. At that point the array has to come off before the roof can be replaced.
The electrical side, disconnecting and recommissioning the system, belongs to a solar electrician. Our side is the roof: everything between the rails and the deck. We schedule both so the array spends as little time off the roof as possible.
What the work covers
Panel Detach Before Reroofing
Once the system is safely shut down and disconnected, panels come off rail by rail and are stored flat and padded on site or in a secure spot, labeled by position. Rails and mounts are removed and the attachment points photographed before the old roof comes off, so the array goes back exactly where it was. Any damage to panels or racking found during removal is documented before we touch the roof, so nobody argues later about what was already there.
Reinstall and Mount Flashing
Every solar attachment is a lag bolt into a rafter, and every one needs a flashed mount. On the new roof we locate each rafter, install mounts with purpose-made flashing woven into the shingle courses, and seal the bolt under the flashing rather than on top of it. Rails and panels then go back on to the original layout. Mounts that were simply caulked to the old shingles are exactly how solar roofs leak, and that is the shortcut we do not take.
Rack Mount Leak Repair
Leaks under an array usually trace to one or two mounts where the flashing was skipped or the sealant dried. Finding them means working under the panels with a light and sometimes lifting a panel or two. We reflash the failed mounts with proper flashing blocks, replace cracked shingles around them, and check the rest of the attachments while the panels are open. If the roof under the array is near the end of its life, we will tell you before investing in spot repairs.
What drives the price
What Panel Removal and Reinstall Costs Depend On
Detach and reset pricing follows the size of the array and the roof work underneath it.
Number of panels
More panels mean more handling and mounts.
Racking type
Some rail systems come apart faster than others.
Roof work
Repair under part of the array or a full replacement.
Mount flashing
New flashed mounts at every attachment.
Storage
Panels stored on site or moved and secured.
Electrical
Disconnect and recommissioning by a solar electrician.
Local conditions
First Replacements Under Atlanta Solar Arrays
Georgia's owner-occupied housing is among the newest in the country, so many Atlanta arrays sit on roofs that are still on their first set of shingles and will need their first full replacement while the panels keep producing. The good news is timing: a standard shingle replacement here usually takes one to three working days, so with the electrician lined up, an array is typically off the roof for a short window rather than a season.
What is included
What a Solar Detach and Reset Includes
- Coordination with a solar electrician for shutdown
- Photos of the array layout and every attachment
- Panels and racking removed and labeled
- Padded, secure storage for panels
- Roof repair or full replacement underneath
- Rafters located for every mount
- Flashed mounts woven into the new shingles
- Rails and panels reset to the original layout
- Photos of the finished roof and array
Step by step
How a Solar Detach and Reset Runs
- 1
Call to plan it
Tell us the roof issue and the system size.
- 2
Coordinate the electrician
Shutdown and recommissioning scheduled.
- 3
Photograph the array
Layout and every attachment recorded.
- 4
Detach and store
Panels and racking removed and protected.
- 5
Repair or reroof
The roof work done with the array off.
- 6
Flash every mount
New flashed mounts into the new roof.
- 7
Reset the array
Rails and panels back on the original layout.
Timeline
How Long the Array Is Off the Roof
On a typical home the array is off the roof for the length of the roof work plus a day on each side for removal and reset. A standard shingle replacement usually takes one to three working days.
The bigger variable is scheduling the electrician for shutdown and recommissioning. We book both ends before the first panel comes off, so the system is not left waiting.
Questions we hear
Solar and Roofing Questions
Yes. The roof under the array cannot be replaced with the panels in place.
A solar electrician handles shutdown and recommissioning. We handle everything on the roof side and coordinate the timing.
Not when every mount is flashed into the new shingles. Caulk-only mounts are what leak.
If the roof is past its middle age, usually yes. It avoids paying to detach the array later.
Often. We lift only the panels around the leaking mount when that is enough.
They are labeled, padded and stored flat in a secure spot.
Only for the days the array is off the roof.
Related work
Replacement and Installation Work
Atlanta, GA service office
1421 Peachtree St NE FL. 3, Atlanta, GA 30361
Talk to a roofer today
Replace the roof without trading it for mount leaks
Call to plan it. We coordinate with your solar electrician, redo the roof and flash every mount before the array goes back on.